Loading tool...
The ITU Radio Frequency to Wavelength Conversion tool calculates the wavelength for frequencies from 8.3 kHz to 11.2 GHz. Select your region to view the primary ITU allocation for the entered frequency.
Enter your parameters below to calculate results.
The ITU Radio Frequency to Wavelength Conversion tool converts a radio frequency into its corresponding wavelength. The calculator is useful for antenna design, RF planning, spectrum studies, and quick comparisons of frequency bands across ITU radio regions.
Enter a frequency value, select the unit, and the tool calculates the wavelength using the speed of light. The frequency range shown on the page extends from 8.3 kHz to 11.2 GHz, covering part of the VLF range through LF, MF, HF, VHF, UHF, and part of SHF.
Frequency and wavelength are related through the speed of electromagnetic propagation:
c = λ × f
Therefore:
λ = c / f
and:
f = c / λ
| Symbol | Meaning | Unit |
|---|---|---|
| λ | Wavelength | m |
| f | Frequency | Hz |
| c | Speed of light in vacuum | 299,792,458 m/s |
For quick RF estimates, engineers often use c ≈ 300,000,000 m/s. This gives the convenient shortcut:
Wavelength in meters ≈ 300 / frequency in MHz
| Frequency | Approximate Calculation | Wavelength |
|---|---|---|
| 1 MHz | 300 / 1 | 300 m |
| 10 MHz | 300 / 10 | 30 m |
| 100 MHz | 300 / 100 | 3 m |
| 1000 MHz | 300 / 1000 | 0.3 m |
| 2.4 GHz | 300 / 2400 | 0.125 m, or 12.5 cm |
| 5.8 GHz | 300 / 5800 | 0.0517 m, or 5.17 cm |
| Band | Frequency Range | Approximate Wavelength Range | Typical Context |
|---|---|---|---|
| VLF | 3 kHz to 30 kHz | 100 km to 10 km | Navigation, time signals, and special low-frequency systems. |
| LF | 30 kHz to 300 kHz | 10 km to 1 km | Long-wave communication and beacons. |
| MF | 300 kHz to 3 MHz | 1 km to 100 m | AM broadcast and maritime communication. |
| HF | 3 MHz to 30 MHz | 100 m to 10 m | Shortwave, amateur radio, aviation, and long-distance links. |
| VHF | 30 MHz to 300 MHz | 10 m to 1 m | FM broadcast, airband, land mobile, and marine radio. |
| UHF | 300 MHz to 3 GHz | 1 m to 10 cm | Mobile, TV, Wi-Fi, Bluetooth, GPS, and many short-range systems. |
| SHF | 3 GHz to 30 GHz | 10 cm to 1 cm | Microwave links, radar, satellite, and high-speed wireless systems. |
Enter the frequency value and choose the correct unit, such as Hz, kHz, MHz, or GHz. The calculator converts the input to hertz and then applies λ = c / f. If the page also shows an ITU allocation result, select the appropriate ITU region before interpreting the service allocation.
For example, a frequency of 100 MHz gives:
λ ≈ 300 / 100 = 3 m
A frequency of 433 MHz gives:
λ ≈ 300 / 433 = 0.693 m
The International Telecommunication Union divides the world into three radio regions for spectrum allocation. Allocations and operating conditions for the same frequency can vary by region, so choose the region that matches the intended operating location.
| Region | General Coverage |
|---|---|
| Region 1 | Europe, Africa, the Middle East west of the Persian Gulf, Mongolia, and the area of the former Soviet Union. |
| Region 2 | The Americas, Greenland, and some eastern Pacific islands. |
| Region 3 | Most of Asia outside the former Soviet area, plus Oceania and much of the Pacific region. |
An ITU allocation identifies which radiocommunication services may use a frequency band at the international or regional level. It does not automatically grant permission to transmit. Actual use can depend on national regulations, licenses, channel plans, maximum power, emission type, bandwidth, duty cycle, equipment certification, and local coordination requirements.
For compliance work, use the calculator only as a technical reference and check the official frequency allocation table from the relevant national regulator.
The wavelength calculated from the speed of light in vacuum is the free-space wavelength. In a cable, PCB trace, dielectric material, or waveguide, electromagnetic waves travel more slowly. The practical wavelength is shortened by the velocity factor of the medium.
A common engineering relationship is:
λmedium = λfree-space × velocity factor
For antenna elements, transmission lines, and PCB RF layouts, use the dielectric constant or velocity factor from the cable, laminate, or component datasheet.
Wavelength conversion is often used to estimate antenna element length. In free space:
| Antenna Fraction | Formula | Example at 100 MHz |
|---|---|---|
| Full wavelength | λ | 3 m |
| Half wavelength | λ / 2 | 1.5 m |
| Quarter wavelength | λ / 4 | 0.75 m |
Real antennas are affected by conductor diameter, ground plane, matching network, nearby objects, enclosure materials, and end effects. Use these values as initial estimates rather than final dimensions.
| Mistake | Why It Matters |
|---|---|
| Mixing MHz and GHz | A factor of 1000 error in frequency creates a factor of 1000 error in wavelength. |
| Using free-space wavelength for a cable directly | Cables and PCB traces have a shorter wavelength because signals travel below c. |
| Assuming ITU allocation means legal authorization | National rules and licenses still control actual operation. |
| Ignoring antenna environment | Nearby metal, plastic, ground planes, and the user's hand can shift the resonant frequency. |
Because the wave speed is fixed for a given medium. When frequency increases, more wave cycles fit into the same distance, so each wavelength becomes shorter.
Use 299,792,458 m/s when you need the exact speed of light in vacuum. Use 300,000,000 m/s for quick RF estimates where the rounding error is smaller than practical antenna and layout tolerances.
No. This page is for electromagnetic waves. Sound travels much more slowly than light, so its wavelength must be calculated using the speed of sound in the relevant medium.
The dielectric inside the cable slows the signal. The wavelength in the cable equals the free-space wavelength multiplied by the cable velocity factor.