
STM32G474MET6: 184ps HRTIM, Dual-Bank Flash & LQFP80
Building digital power on STM32G474MET6? Map LQFP80 HRTIM fault pins, verify 512KB dual-bank flash updates and check MET3/RET6 limits. Request a quote.
Read more →
The ADBMS6948 is a multi-cell battery monitor with the industry's first parallel measurement architecture, which measures up to 16 series-connected battery cells with a TME of less than 3 mV over the full temperature range and lifetime. The parallel measurement architecture ensures the lowest external component cost in its category. It is the industry's only battery management system with redundancy on voltage, current, temperature, and overcurrent detection. The cell voltage measurement input range of -2.0 V to 5.5 V makes ADBMS6948 suitable for most battery chemistries and allows the measurement of voltages across bus bars. All 16-cells can be measured simultaneously and redundantly with two individual analog-to-digital converters (ADCs), C-ADC and S-ADC, respectively. The ADCs have a sampling rate of 4.096 MHz and a conversion time of up to 1 ms. Higher noise reduction can be achieved by subsequent programmable digital IIR filters.The ADBMS6948 also provides the best-in-class integrated bidirectional current measurement capability. It measures the current flowing in and out of the battery module by measuring the voltage drop over an external sense resistor with an input offset voltage of 1 µV and 0.1% gain error over a lifetime. The additional current channel ADC can be synchronized with the cell voltage measurements. This combination of parallel, synchronous, and precise voltage and current measurement provides the ability to achieve an accurate state of charge (SOC), state of power (SOP), and state of health (SOH) estimation at the microcontroller unit (MCU). The ADBMS6948 also provides an integrated coulomb counter, which can be used to offload MCU overheads for precise SOC estimation.The ADBMS6948 also provides the only Li-ion cell monitor with an integrated overcurrent (OC) detection feature with a less than 2µs overcurrent response time. The dedicated overcurrent pins can be used to connect to an external switch driver to control the switch in the system. The dedicated OC pins with less than 2µs reaction time in ADBMS6948 allow lower rating components for protection devices on the power distribution unit. The ADBMS6948 OC detection algorithm takes into account the limitation of the traditional comparator-based OC detection which cannot detect OC events under short time period glitches and gives false detection under high load conditions. The ADBMS6948 OC detection algorithms work in the energy domain. The algorithm uses the measured current value to determine the heat generated in the MOSFET. Using additional thermal model parameters, the algorithm estimates the temperature rise of the FETs to determine the OC condition.The ADBMS6948 also provides a low power monitoring (LPM) feature that can be used to prevent thermal runaway conditions even when the MCU is in the sleep state. The ADBMS6948 not only measures the cell voltage, cell temperature, and pack current in this mode, but also monitors the rate of change of each cell voltage (dV/dt), the rate of change of temperature of each connected battery temperate (dT/dt), and the rate of change of pack current (dI/dt) therefore provides an early detection of any thermal runaway parameters. The ADBMS6948 generates an interrupt on the dedicated FAULTB pin when any of the preprogrammed over or under thresholds on either cell voltage, cell temperature, or delta measurements are violated.The ADBMS6948 also has additional analog voltage channels that can be used to measure temperature through external NTC, perform DC-link voltage, and switch/FET diagnostic measurements. The ADBMS6948 provides a serial-peripheral interface (SPI), with a maximum operating frequency of 4MHz for configuration, measurement trigger, and readback. The ADBMS6948 can be powered directly from the battery stack or from an isolated supply. It includes passive balancing with individual pulse-width modulation (PWM) duty-cycle control, and up to 300mA discharge current for each non-consecutive cell. Other features include an onboard 5V regulator and a sleep mode where current consumption is reduced to 4µA.
YG GROUP (YUGUANG INTERNATIONAL(HK)CO.,LTD) supports reliable sourcing through quality controls and compliance documentation. Please confirm product requirements, applicable certifications and supporting documents before ordering.
ADBMS6948 is an authentic electronic component manufactured by Analog Devices, categorized under Power Management ICs. It is supplied in the standard manufacturer-specified package footprint, providing industry-standard mechanical dimensions and terminal configurations for board-level assembly. Full pinout configurations, physical footprint drawings, and rated operating tolerances are documented in the official ADBMS6948 datasheet above.
Electronic component spot-market pricing for ADBMS6948 fluctuates based on real-time global availability, production date codes, minimum order quantities (MOQ), and packaging formats (e.g., Reel, Tube, Tray). Using an RFQ ensures you receive accurate, real-time volume pricing tied to verified, traceable inventory rather than stale catalog estimates.
Lead times for ADBMS6948 depend on whether stock is dispatched from our central hub or regional franchise partners. Ready-to-ship inventory typically leaves the warehouse within 1–3 business days following quality inspection, while factory-direct or back-ordered allocations are confirmed with an estimated ship date upon RFQ reply.
Loading articles…
Loading articles…

Building digital power on STM32G474MET6? Map LQFP80 HRTIM fault pins, verify 512KB dual-bank flash updates and check MET3/RET6 limits. Request a quote.
Read more →
Sourcing ADS1278IPAPT for simultaneous 24-bit DAQ? Compare 144kSPS vs 31mW/ch pin-selected modes, SPI/frame-sync data and PowerPAD. Request a quote.
Read more →
Designing multi-channel RF clocks on LMX2594RHAT? Separate 15GHz phase sync from JESD204B SYSREF capture and lock VQFN-40 reel specs. Request a quote.
Read more →
Approving TMS320F28379DPTPT for production? Verify the 9-pair HLQFP176 ADC map, CPU1/CPU2 IPC boot and PowerPAD solder spec vs ZWT. Request a BOM quote.
Read more →Loading related products…
| Picture | Part Number | Manufacturer | PDF / RoHS | Stock | Action |
|---|---|---|---|---|---|
| Analog Devices | 7,280 | ||||
| Analog Devices | -- | 9,040 | |||
| Analog Devices | 9,520 | ||||
| Analog Devices | 6,020 | ||||
| Analog Devices | 7,970 | ||||
| Analog Devices | 4,740 | ||||
| Analog Devices | 9,690 | ||||
| Analog Devices | 7,430 | ||||
| Analog Devices | 5,650 | ||||
| Analog Devices | 5,310 |