Pin 4 (RT/CLK) accepts the external synchronization clock or frequency-setting resistor. Pin 5 (EN) is a separate precision enable and UVLO input—verify clock voltage thresholds, pulse widths and frequency range in DS41976 before driving RT/CLK.
No. According to the AP64350 data sheet, internal ±6% frequency spread spectrum (FSS) operates in resistor-timed mode and is automatically disabled when RT/CLK locks to an external clock. Evaluate conducted and radiated EMI in the exact mode your production board uses.
No. Internal FSS lowers narrowband spectral peaks, but hot-loop input capacitor placement, node area, inductor shielding, light-load ripple and cable filtering still govern whether the finished assembly passes CISPR/EN limits.
By Eyki Chen
AP64350SP-13 is a 40 V, 3.5 A SO-8EP synchronous buck converter whose RT/CLK pin sets resistor timing or locks to an external clock. Because external synchronization automatically turns off the chip's internal ±6% frequency spread spectrum (FSS), 24 V industrial PLC and sensor boards must choose between fixed harmonic placement and spread-spectrum peak reduction—then prove EMC on the real PCB.
RT/CLK) owns frequency and clock sync: Pin 5 (EN) handles precision enable and UVLO dividers only—never feed a sync clock into EN.RT/CLK from an external clock disables FSS.SWNo. Although they share the 40 V, 3.5 A rating and SO-8EP package, AP64351SP-13 and AP64352SP-13 reassign control pins for programmable soft-start and compensation adjustments, making them pin-incompatible with an AP64350SP-13 RT/CLK circuit.
Include the complete AP64350SP-13 (-13 reel) ordering code, build quantity, need-by schedule, MSL/lot traceability requirements, and state explicitly if automotive AP64350Q qualification is required rather than standard industrial material.
AP64351SP-13AP64352SP-13In the Diodes Incorporated AP64350 data sheet (DS41976 Rev. 5-2), connecting a programming resistor to Pin 4 (RT/CLK) sets nominal switching frequency while activating internal ±6% frequency spread spectrum to lower peak conducted and radiated CISPR/EN detector readings. Feeding a valid external clock into RT/CLK switches the internal PLL into synchronization mode and disables internal FSS.
Decide upfront whether your board suffers more from narrowband CISPR peaks or intermodulation beat notes. On multi-rail PLC backplanes or precision ADC cards, AP64350SP-13 RT/CLK synchronization places switching harmonics at predictable multiples outside sensitive analog passbands and eliminates low-frequency beat tones between adjacent converters. On standalone 24 V nodes with no sensitive receiver window, resistor-timed spread-spectrum EMI reduction often trims input-filter size.
Before wiring an FPGA or MCU clock to RT/CLK, check logic-high/low thresholds, pulse-width bounds and startup/clock-loss behavior in DS41976, and verify minimum controllable on-time ($t_{ON(\text{min})}$) at peak 24 V or 36 V line surges. Pushing switching frequency toward 2 MHz on a 24 V-to-3.3 V rail can hit minimum on-time foldback while driving SO-8EP switching losses up sharply.
| Operating regime | What the circuit controls | Pre-compliance test to run |
|---|---|---|
| Resistor-timed + ±6% FSS | Nominal $f_{SW}$ via RT resistor | Conducted/radiated quasi-peak and average scans across line/load |
RT/CLK external sync | Exact phase/frequency lock to system clock | Spur placement in ADC/comms bands plus clock-startup transient check |
| Light-load pulse-skipping | PFM efficiency vs low-frequency output ripple | Idle ripple and acoustic/sub-harmonic noise—compare Eco-mode vs FCCM trade-offs on TPS53513RVER |
Table 1: Bench verification matrix across timing and load regimes | Source: Diodes Incorporated AP64350 Data Sheet, DS41976 Rev. 5-2 | Compiled by: YG GROUP
Also test power-up sequencing when the 24 V bus rises before the host MCU or FPGA begins driving RT/CLK. Verify that the timing network lets the converter soft-start cleanly without output overshoot or inductor saturation, and confirm transition behavior if the external clock stops during a system reset. On the factory floor, pair your AP64350SP-13 BOM line with the exact shielded inductor saturation current (ISAT), DC-bias-derated ceramic output capacitance, X-ray solder-void limits under the SO-8EP thermal pad and -13 reel orientation so pre-compliance EMC results carry straight into volume production.
Neither clock sync nor spread spectrum will rescue a wide high-$di/dt$ input capacitor loop. Follow the SO-8EP buck layout in the AP64350SP-EVM User Guide: place low-ESR ceramic input bypass capacitors immediately across VIN and GND, keep the SW copper island compact, route FB away from inductor fringing flux, and stitch the underside exposed pad into internal ground planes—matching the thermal and EMC workflow in 40 V buck EMI and thermal planning on LMR14050SSQDDARQ1.
As summarized in Diodes Incorporated's AP64xxx family announcement, sibling 40 V / 3.5 A parts trade away RT/CLK to expose other analog pins inside the 8-pin package:
| Candidate MPN | Key functional difference vs AP64350SP-13 | Why a blind BOM swap fails |
|---|---|---|
AP64351SP-13 | Fixed 500 kHz switching; replaces RT/CLK with adjustable soft-start (SS) | External RT resistor or sync clock on Pin 4 breaks startup behavior |
AP64352SP-13 | Adjustable soft-start / internal compensation variant | Different external passive network and pin assignment in SO-8EP |
Table 2: Pin-function differences across the 3.5 A AP6435x family | Source: Diodes Incorporated AP64xxx Family Release | Compiled by: YG GROUP
Keep standard industrial AP64350SP-13 distinct from automotive AP64350QSP-13 as well; specify Q grade upfront whenever AEC-Q100 documentation is required.
Check external bootstrap (BST) capacitor selection and undervoltage-lockout resistor tolerances across -40 °C to +125 °C junction corners at the same time: a 100 nF ceramic BST capacitor placed directly between BST and SW keeps high-side gate drive crisp, while precision EN divider resistors stop noisy 24 V industrial contactors from chattering the converter on and off during brownouts.
Lock the AP64350SP-13 code, RT resistor or clock driver, shielded inductor MPN and SO-8EP stencil aperture together after EMC sign-off. To source through the YG GROUP Diodes Incorporated page, submit AP64350SP-13 (-13 tape-and-reel), build quantity, need-by date and lot-traceability rules via the RFQ form.
AP64xxx Release), October 2019.